VTG 2026 Meet us at VTG 2026 — Booth A560, SECC Ho Chi Minh City, 14–17 October Booth A560 · 14–17 Oct Book a meeting ›

Prestige R2 ProCustomer login

Prestige R2 Pro - How to Replace Inlet Filters

Every step links to its own moment in the video, so you never hunt for the right part again.

  • 18 steps
  • 70 instructions
  • 1 video
  • Updated 2026-04-20

How to Replace the Intake Filter – Prestige R2 Pro

  1. 0:01Overview
  2. 0:25Remove Intake Filter Access Panel
  3. 0:57Clamp Ink Line (Yellow Example)
  4. 1:10Prepare Carriage for Safe Access
  5. 1:30Remove Covers
  6. 1:50Secure White Ink Lines
  7. 2:05Remove Diverter and White Dampers
  8. 2:23Remove Old Intake Filter
  9. 3:00Install New Intake Filter
  10. 3:38Prime the Line
  11. 4:14Reinstall Components
  12. 4:40Reassemble Covers
  13. 5:11Power On & Cleanup
  14. 5:35Reinstall Intake Panel
  15. 5:50Reinstall Media Feed Reel
  16. 6:10Reload Media
  17. 6:34Perform Fill Ink & Cleaning
  18. 7:19Final Nozzle Check
Written steps 18

Overview

Watch this part0:01
  1. Remove the media from the printer.
  2. Raise the pinch roller lever.
  3. Roll the media up.
  4. Rotate the left knob counterclockwise.
  5. Slide the media bracket out.
  6. Catch the media and set it aside.

Remove Intake Filter Access Panel

Watch this part0:25
  1. Remove the panel covering the intake filters.
  2. Remove all 8 screws securing the panel.
  3. Set the panel aside to expose the inlet filters.

Clamp Ink Line (Yellow Example)

Watch this part0:57
  1. Identify the inlet filter for the ink color being replaced (yellow in this example).
  2. Clamp the ink line above the filter.

Prepare Carriage for Safe Access

Watch this part1:10
  1. Open the top lid of the printer.
  2. Press the Left Arrow key once to disengage the carriage from the capping station.
  3. Press and hold the Left Arrow key to move the carriage to the center of the bed.
  4. Press the Emergency Stop button to power the printer off.

Remove Covers

Watch this part1:30
  1. Loosen all screws on both sides of: Printer carriage cover
  2. Do not fully remove the screws.
  3. Remove both covers once loosened.
  • Daughterboard cover

Secure White Ink Lines

Watch this part1:50
  1. Clamp all white ink lines.
  2. Place paper towels beside the carriage to catch ink.

Remove Diverter and White Dampers

Watch this part2:05
  1. Remove the diverter by removing one screw on each side.
  2. Remove all white dampers.
  3. Place the dampers on the paper towels.

Remove Old Intake Filter

Watch this part2:23
  1. Locate the ink tube connected to the intake filter being replaced.
  2. Clamp the ink line.
  3. Place paper towels under the filter area.
  4. Cut the tube above the filter: Cut straight across.
  5. Cut the tube on the opposite side of the filter.
  • Cut as close to the filter as possible.
  • If remaining tube length is too short, use the ink tube connectors and extensions provided with the printer.

Install New Intake Filter

Watch this part3:00
  1. Identify the side of the new filter labeled “INLET”.
  2. Ensure the INLET side faces up.
  3. Push the ink tube onto the inlet side until fully flush.
  4. Push the opposite tube onto the other side of the filter.
  5. Ensure both tubes are fully seated to avoid air leaks. TIP
  • Use a paper towel for better grip if ink is on the tubing.

Prime the Line

Watch this part3:38
  1. Unclamp the ink line.
  2. Go to the front of the printer.
  3. Use a syringe to pull ink from the damper.
  4. Verify: Steady ink flow
  • No air bubbles

Reinstall Components

Watch this part4:14
  1. Reinstall the yellow damper.
  2. Reinstall all white dampers.
  3. Secure the diverter using the two screws.
  4. Release all white ink tube clamps.

Reassemble Covers

Watch this part4:40
  1. Reinstall the printer carriage cover.
  2. Tighten all screws on both sides.
  3. Reinstall the daughterboard cover.
  4. Tighten all screws.

Power On & Cleanup

Watch this part5:11
  1. Release the Emergency Stop button.
  2. Power the printer on.
  3. Allow the carriage to dock onto the capping station.
  4. Remove paper towels.
  5. Clean any spilled ink.
  6. Organize ink tubes and filters to avoid pinching.

Reinstall Intake Panel

Watch this part5:35
  1. Reinstall the intake filter panel.
  2. Secure it using the original 8 screws.

Reinstall Media Feed Reel

Watch this part5:50
  1. Slide the media bracket back onto the rails.
  2. Place media into position.
  3. Push the left bracket inward.
  4. Rotate the knob clockwise to tighten.

Reload Media

Watch this part6:10
  1. Feed media under the tension rod from the back.
  2. Pull media through the front.
  3. Apply tension from both sides.
  4. Lower the pinch roller lever.
  5. Press the Down Arrow key to advance media.
  6. Position the media guides.

Perform Fill Ink & Cleaning

Watch this part6:34
  1. Bypass the printer cover sensor using a metal object.
  2. On the control panel: Menu → Head Maintenance → Fill Ink → Two Head
  3. Run fill ink for 30 seconds (timer starts when ink flows).
  4. Press Cancel.
  5. Perform two head cleanings.

Final Nozzle Check

Watch this part7:19
  1. Menu → Head Maintenance → Head Status.
  2. Print a nozzle check.
  • If nozzle check is good: Intake filter replacement is successful.
  • If nozzle check is poor: Contact DTF Station Tech Support.

Stuck on a step?

Your authorized dealer and our factory support team answer on Discord — the fastest route to a person who knows this machine.

Get support